Inverted perovskite solar cell based on co-absorbed self-assembled monolayer achieves 24.68% efficiency

Share

Researchers in China have developed an inverted perovskite solar cell based on a hole transport layer (HTL) with a self-assembled monolayer (SAM) aimed at reducing passivating defects and increasing efficiency.

Inverted perovskite cells have a device structure known as “p-i-n”, in which hole-selective contact p is at the bottom of intrinsic perovskite layer i with electron transport layer n at the top. Conventional halide perovskite cells have the same structure but reversed – a “n-i-p” layout. In n-i-p architecture, the solar cell is illuminated through the electron-transport layer (ETL) side; in the p-i-n structure, it is illuminated through the HTL surface.

The research team used SAMs made of 2-chloro-5-(trifluoromethyl)isonicotinic acid, referred to as PyCA-3F, while the HTL was made with [2-(9H-Carbazol-9-yl)ethyl]phosphonic acid (2PACz). A co-adsorbed approach (CA) was used for the SAM application. It consists of growing the perovskite films on 2PACz substrates with and without PyCA-3F.

The cell was built with a substrate made of indium tin oxide (ITO), the 2PACz HTL, a perovskite absorber, an electron transport layer (ETL) relying on buckminsterfullerene (C60), a bathocuproine (BCP) buffer layer, and a copper metal contact.

Tested under standard illumination conditions, the device achieved a “certified” efficiency of 24.68% efficiency, while the control device was 23.3%-efficient. The scientists did not name the third-party entity certifying the result.

The group postulated that the presence of PyCA-3F plays a pivotal role in “mitigating the occurrence of physical nanovoids” at the buried interface. “This notable increase stands as a strategic advantage, contributing to the effective reduction of interfacial traps and nonradiative centers at the buried interface,” it said.

The approach was found to effectively diminish 2PACz’s aggregation, while enhancing surface smoothness and increasing work function for the modified SAM layer, which the researchers said provides a flattened buried interface with a favorable heterointerface for perovskite.

To test the proposed approach on other solar cell technologies, the scientists also fabricated 2PACz/PYCA-3F-based organic solar cells (OSCs). They used an open-air blade coating method to make the p-i-n structured OSC devices. The resulting devices had efficiencies ranging from 17.71% to 19.51%. The best performing OSC was based on PM1:PTQ10:m-BTP-PhC6.

The researchers noted that the OSC samples achieved “one of the best results for open-air blade coating” cast by the co-adsorbed strategy and the novel small molecule acid SAM. They also noted that the method improved the stability of both perovskite and OSC devices. “After a 1000-hour maximal power point tracking, the encapsulated PSCs and OSCs retain approximately 90% and 80% of their initial efficiencies, respectively,” stated the team, adding that the operational stability, as indicated by maximal power point tracking results, underscored the “superiority” of the co-adsorbed approach for both PSC and OSC technologies.

“In summary, our work presents a facile, rational, and effective co-adsorbed strategy to enhance the performance of SAM-based devices, resulting in efficiency breakthroughs for both PSCs and OSCs based on p-i-n device structure, coupled with enhanced operational stability,” the research group said.

The research was recently presented in the paper “Co-adsorbed self-assembled monolayer enables high-performance perovskite and organic solar cells,” published in nature communications. The research team included scientists from China’s Southern University of Science and Technology and Hong Kong Polytechnic University, and the Chinese University of Hong Kong (CUHK).

This content is protected by copyright and may not be reused. If you want to cooperate with us and would like to reuse some of our content, please contact: editors@pv-magazine.com.

Popular content

Chinese developer switches on world’s largest perovskite-based PV plant
09 December 2024 MicroQuanta, a Chinese perovskite solar specialist, has commissioned a 8.2 MW PV facility based on its 90 W perovskite panels in eastern China.